Water & Wastewater

Real-time monitoring for
water and wastewater.

Municipal utilities and water operators are replacing SCADA and outdated standalone monitors with AccuDose. Same real-time visibility. 60 to 90% less.

  • Cellular monitoring. No radio network, no on-site internet.
  • No SCADA programming, no integrator, no IT project.
  • Alarms by SMS and email the moment something trips.
  • Installs inside the existing control panel in under an hour.
  • Lifetime hardware warranty on every unit.
90%Less than SCADA
60%Less than standalone cellular
<1 hrTypical install
LifetimeHardware warranty

AccuDose vs. traditional SCADA

Traditional SCADA
$$$$$
Legacy standalone cellular
$$$
Specialized integrator
Required
Deployment time
Weeks to months
AccuDose deployment
Hours. No programming.
AccuDose cost
60 to 90% less
Typical figures for the industry. Your quote is based on your sites.
The problem

Legacy monitoring is
breaking municipal budgets.

Water and wastewater utilities have always needed remote monitoring. Knowing when a pump fails, when a wet well is near overflow, or when a generator goes offline is not optional.

For decades the only real option was SCADA: infrastructure-heavy systems that need specialized integrators, ongoing software licensing and IT support most small utilities do not have. Standalone cellular monitors came along as an alternative, but they are limited in what they can see and still expensive for what they deliver.

01

SCADA costs are prohibitive

Full SCADA deployments run tens of thousands of dollars per site, before annual licensing and maintenance.

02

Standalone monitors are outdated

Legacy dial-up and early cellular monitors have no real-time data, no cloud access, no historical logging and no analog measurement.

03

Integration and IT overhead

Traditional systems need network infrastructure, specialized configuration and ongoing vendor support most utilities cannot afford.

04

Small utilities left behind

Smaller municipal systems and rural water districts do not have the budget or staff for enterprise SCADA. They still need real-time visibility.

Legacy SCADA, typical costs

Hardware per site
From $4,000
Integration and programming
$5,000 to $20,000
Annual software licensing
$2,000 to $10,000 a year
Network and IT infrastructure
Required
Specialized integrator
Required
Deployment time
Weeks to months
Ongoing maintenance
High
Cloud and mobile access
Often limited or extra

Industry-typical ranges, before site-specific extras.

The solution

Everything SCADA does.
At a fraction of the cost.

AccuDose delivers real-time monitoring and control for water and wastewater infrastructure over LTE-M cellular. No integrators, no on-site networking, no software licensing.

Connect it to the equipment signals you already have, power it on, and it starts sending live data to the cloud. Alarms go out by SMS and email. History is logged automatically. Your whole team sees the same real-time picture from any device.

FeatureLegacy SCADAAccuDose
Real-time alarmsYesYes
Historical loggingYesYes
Analog monitoringYesYes
Remote controlYesYes
Integrator neededRequiredNot needed
IT and networkingRequiredBuilt-in cellular
Plug-and-play setupNoYes
Lifetime warrantyNoYes
CostBaseline60 to 90% less
Global LTE-M cellularBuilt-in SIM connects automatically across Verizon, AT&T and T-Mobile. No on-site internet.
Plug-and-play deploymentConnect to existing equipment signals, power on, and start transmitting. No programming.
Real-time dataLive readings, immediate SMS and email alarms, and full historical trending from any device.
Lifetime warrantyEvery AccuDose unit ships with a lifetime hardware warranty. Built for remote infrastructure.
Monitoring applications

Every application SCADA covers.
AccuDose handles them all.

From lift stations to chemical dosing, the same real-time monitoring and alarm coverage as SCADA. Deployed in hours, not weeks.

Lift and pump stations

Lift and pump stations

Pump run status, wet well level, high-level alarms, VFD and motor faults, runtime hours, floats and power failure across single and multi-pump sites.

  • Multi-pump run, fault and runtime
  • Wet well level (analog)
  • VFD and motor fault monitoring
  • High level, float and power fail alarms
Tank and well sites

Tank and well sites

Tank level, pressure, well call status, well run confirmation, pump faults and automated refill setpoints.

  • Tank level and pressure
  • Well call and run confirmation
  • Automated refill setpoints
  • Pump fault and power fail
Wet wells

Wet wells

Continuous wet well level with high-level alarm triggers, float switch status and overflow visibility.

  • Continuous level monitoring
  • High level alarm triggers
  • Float switch status
  • Overflow prevention alerts
H₂S odor control

H₂S odor control

Chemical feed pump run, dosing rate and flow, chemical tank level, and remote enable or disable of dosing.

  • Chemical feed pump run and fault
  • Dosing rate and flow
  • Tank level
  • Remote enable and disable
Generator monitoring

Generator monitoring

Utility power status, generator run and fault, runtime hours, fuel level, battery voltage and start failures.

  • Utility power and generator run
  • Generator fault and start failure
  • Fuel level and battery voltage
  • Runtime hour tracking
Chemical dosing

Chemical dosing

Full chemical pacing control. Dosing rate, feed pump run, tank level, and chemical injection paced from an analog output.

  • Analog output chemical pacing
  • Dosing rate and flow
  • Chemical tank level
  • Feed pump run and fault
Typical deployment

Up and running
in hours, not weeks.

AccuDose installs inside the panel you already have. No new enclosure, no conduit run, no integrator on site. Most sites are live on the dashboard in a single visit.

  1. 01Mount inside the panelAccuDose mounts inside the existing lift station or pump control panel. No new enclosure, no conduit run.
  2. 02Wire to the signalsLevel transmitters to analog inputs. Pump run, fault, float and power fail contacts to digital inputs.
  3. 03Power onThe unit connects to the strongest available carrier on its own. No SIM to manage, no network to configure.
  4. 04MonitorLive data shows up in the dashboard within minutes. Set alarm thresholds and contacts from any device.
  5. 05Add the next siteEvery additional station deploys the same way, and every station lands on the same dashboard.
Operational benefits

Fewer truck rolls.
No surprises.

Real-time data changes how a utility runs its remote sites. Crews respond to what is actually happening, not to a schedule.

01

Catch failures immediately

Pump trips, high wet well level, power loss. The alarm reaches your phone the moment it happens.

02

Stop the overflow

High-level alarms and float status give you time to act before a wet well becomes an SSO.

03

Send fewer trucks

Check every station from the truck or the office. Drive to the ones that need you.

04

Trend the data

Runtime, levels and analog readings are logged automatically for reports and troubleshooting.

05

One dashboard

Lift stations, tanks, wells and generators on one screen, for the whole team.

06

Scale without a project

Every site deploys the same way. No per-site programming, no integrator, no new servers.

Built for
Municipal utilitiesRural water districtsWastewater plantsContract operatorsSystems without a SCADA budget

Bring your infrastructure
into real-time view.

See which AccuDose unit fits your lift stations, pump stations, tanks and wells, or talk to us about your specific application.